water
Water droplets? Could have been from your ride...but could be entering elsewhere (i.e. the fuel tank). Check your compression and if that is correct, replace the plugs and go from there.
... running head to head for hours today, we GPS'd the GPR at 63.9 and the yellow bullet (heads, pipe, water injection, prop, grate, ignition, etc.) at a blistering 64.5. As Gary said, .6 mph is fas...
My buddies GTi backfires too when blowing the water out. Runs fine otherwise. No reeds in the 720 though. It has the rotary valve.
Yer fuel float done went and sunk. It'll float in water, so that test won't work. Get you another float.
WHAT IS THE IMPELLER TO PUMP CLEARENCE ON A CATERPILLER FRESH WATER PUMP?
...wood remove the cat and put the pop off back to std bring idle back start there and look at the rear water box in side next...
I'm looking into buying this ski with a water logged and then rusted out motor. Just wondering for the sake of buying parts for it what years are compatable and anyhting someone thinks I aught to...
Drain the fuel tank and refill with fresh gas, or add some isopropyl alcohol (known to let the water dissolve in the gas)
Hope this helps.
...side? 15M. Looks cool, but I only have a mouse. It was hard to control, and the skis seem too low in the water. It was fun though. Thanks, Matt Burkhard
...
That's not bad thinking. Have you considered the Pro1200? It will stick to the water better and carve a whole lot better than the SLX. It is however a little slower on pure glass, but I think it&...
...rnace races. >>
Guess you havent heard of powerbooks or I books with airport Mario Back on the water again!! (c:...
...ev/jetski.html
Parts:
SX/SXi/SXiPro Coffman's 'Lightning' series dry exhaust (w/o water injection) - $475 - w/ water injection - $525
MSD Timing advance plate - $15
...
SX/SXi/SXiPro Coffman's 'Lightning' series dry exhaust (w/o water injection) - $475 - w/ water injection - $525
TWIST billet head w/ race gas domes - $60
MSD Timing advance plat...
...me good hp you should see a 1.5 to 3mph gain in speed if you can pull a taller prop.better hookup in the water and great acceration.this is with the set back 12 the normal 12 vein will be a little slo...
I train hard, am experienced with big water, have been held under until blood vessels broke in my eyes, and have jumped many large waves. In my experience surfers have had the attitude that they own t...
...s when installing. Getting them out is no biggie. Why do you need :to replace yours?
I've found water in the pump twice. Once, just maybe i got the o-ring in badly, but I'm sure i didn&#...
...eller shaft, the starter bendix and a few other odds and ends. I ride this machine hard , mostly in salt water. from my personal observations you are going to have problems of one form or another with...
...er low speed jets and smaller high speed jets.
If it has a Factory Pipe on it, increase the headpipe water by using the adjuster on the headpipe.
Bill O'Neal WCM...
I use the hose adapter flush kit to flush the motor. Do I need to rev the engine when flushing out sea water? Or can I just have the engine idle (about 3000 RPM) while the adapter is connected, and if...
...ought one 2 weeks ago and I ride ocean (MA) and i ride a mod x-2 kawi. I found It was great in the rough water <hooked up great in pounding chop was wasnt as good in the corner as the deep intake f...
...ks or jacks
Steel wool or rags
Cover
Draining the Engine and Cleaning the Jet Ski
Step 1Drain the water from the engine as soon as you take it out of the water after your last ride of the seaso...
...rting and you would be there with no problem at all. it takes a lot more hp to push the blaster thru the water because of the drag it creates, hence the race hulls that were manufactured prior to supe...
...ou did was replace the pistons and rings and then the problems started.....it may very well be an air or water leak into the cyl , but did you check the crank index ? did you pressure check the motor ...
From what I am reading these things get up to 72 mph and can sustain high speeds through rough water.
Im checking into this a bit more. Im not saying that Im getting rid of the sxi or the xp, just...
...ged pop-off, needle and seats, and jets - finally it all came together. The only solution is time on the water. Andrew was very helpful - call him.
As for the tour, we'll be with Adrenalin ag...
...as when new- so it's not as common to have to replace that part (unless it's damaged from salt water or other debris). Since it is an axial flow, there's no shimming that can be done, i...
... that ski. Jeff Hain wrote that Jeff was having a little bit of trouble riding the ski wide open on flat water. What it is, is a testament to probably the best standup pilot ever.
PS. I did like t...
...ille just gaining strength from his ordeals. Training at the pool among other things, hey, the guy loves water, can you blame him? lol He is in good spirits, as always.
Anyway, just wanted to upda...
...t it's still running, finally get back up and the ski comes up about 2 seconds later and is FULL of water and dies. So, I hit the start button and nothing. Bilge, bilge, bilge, need to get it run...
Hi,I'm planning on buying a watercraft before the season starts here in ontario canada.I'm looking to buy one for wave jumping and just playing around down here on Lake Huron near Sarnia Ont...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in detail [
why?
]
Latest Posts
|
