speed
... from what you describe that you are already at level of modification where you won't see much more speed increase. That said, here is the list of options you might consider:
stainless steel ...
...turns and stuff, gets upto about 50mph.
The second, gets upto about 50mph, but has low power at lower speed. Meaning slow takeoff, (engine revs high though), cant blast the throttle at about 30 mp...
When I used those carbs on a sxi. My high speed jet was 128 and lows were 85. I think the low speed jet is way too big!! Those carbs do run a little bit better w/ about 20psi pop off, in my applicatio...
Try putting in a lower pitched impellor. Or, try using larger low speed jets and smaller high speed jets.
If it has a Factory Pipe on it, increase the headpipe water by using the adjuster on the h...
.... If the passenger jumped off, it would start right up. The problem can be solved by leaning out the low speed circuit, either by adjusting the low speed needles or by rebuilding the leaky needle and ...
...amaha part number LIT-18571-SD-2K)
2000 GP1200R or GP1200AY
Main Jet 117.5 Pilot Jet 95
High speed screw turn out 1-3/8 Low speed screw turn out (Front) 1-1/2, (Center) 1-3/8, (Rear) 1-1/2...
...r more information about it, and still have a few questions..
1. Can anyone give me a real-world top speed of this machine? I'm not really a speed demon, just curious, and it's still way...
...o does this ratio apply to the Mikuni 'I' series carbs also?
The stock setting for the low speed screws on the GP800 is Front - 2 1/4 turns out & rear 1 7/8 turns out. If I increase ...
Salty..using gps as a speed measuring device, my experience is that at 7150rpm with 13-19 concord, the speed shows 66 to 67. This is with stock
Rider weight is 215#, half tank of fuel, trim at cen...
...ent straight away from us to the first bouy, about 100 to 120 yards out, were David did have the fastest speed of 66 mph. Billy's speed was 60, and most others fell between 58 and 60 mph. One XPL...
Reminds me of Jim and his killerGPR......except he always went backwards in speed. hehehe
...ys!
What I did not like: I am relatively short and only 155 lbs. The boat will get squirrelly at top speed if you do not ride the ass! (Mainly in cross wakes) Every rider that weighed 165 + lbs ju...
...t designed to lift the nose more or just provide stronger hull re- enforcement? How did you measure your speed gains and what were they? I'm sure there are alot of curious speed buyers reading th...
I have thought about buying a drop nozzle and have heard good and bad things, do you loose any top speed and or loss of bottom end down force?? Do they hold up well??
...t performance gains would be appreciated. I talked to the people at Skat Trak and they had no actual top speed or accleration...
...off of the XLL up till 30-35mph, which the XLL would walk right by the GTX then. If you want to keep the speed above 25-30mph, then this machine would be fine, but low speed fun (spin-outs, fishtails,...
The reason Sport Class boats have been discontinued has nothing to do with speed or hull design. Niche boats quit selling in favor of larger barges.
Sharky
...at, good stability, and yes, it will blow that XL800 away when you realize you really DID care about top speed after you've owned it a while. It happens to everybody. You just can't fight it...
...g a little money to fix this annoyance, then it will be a fine recreational ski. Expect to lose a little speed though on smooth wa...
Why? at least the speed would be enough...is there some danger to towing compared to boat or bigger jetski?? I know the skier would propably pull my jetski around, but it shouldn't be a problem i...
...-programmed oem ignition ( I can get that done) and repitching the impellor is the next logical step for speed. Leave the reeds alone. OEM reeds are carbon fiber and they last the longest of any we ha...
... you can do much for them. Other than promoting events, announcing for the IJSBA, color commentating for Speed Vision, and BEING performance alley for the last 2 years on the national tour. Ya maybe y...
...omeone tell me the correct way to line up the drive line after installing a new SBT engine. I get a high speed vibration that Im sure is drive line related when I rev it up. I do not have a long shaft...
...ings,etc.. Will be finished in two weeks. Asking 10,000.00. Of course I'm sure your wondering about speed, it should be around 75-77....
...p was wasnt as good in the corner as the deep intake from westcoast but but its a lot of fun getting max speed before the big-wave.... I give it an A...
... watching the inside of the carbs for any leakage. Make sure to open the throttle so you can see the low speed inlets also. Darin...
... sensitive to the extra load applied . Losses in Rpm of 100 -300 rpms are typical , yes a slight gain in speed 0.5 -1mph can be had ,but I am concerned that the extra load will cause the engine to be ...
...h tray that you got out of it. If he can't see the light then maybe he should be shopping for a ten speed.
I have a 97' SLTX with about 120 hours on it and as part of my prep for the sea...
... the updated version of the Adjust-A-Thrust for the GPR 1200 have shown a 1.5 to 2.0 mph increase in top speed by GPS. Still working on the hard data, hope to have some next week, will post when we ha...
...6.97.53.74/guides.htm - I suggest the high-res version (Sea-Doo 800) but the low-is fine if you on a low-speed connection.
If you have any problems, give us a call in the morning, 8-5 EST. 877-330...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...