problem
What kind of primer are you using? I've seen that problem with the 'pushbutton' type where if you leave the fuel 'on', any pressure in the tank will push gas through it and in...
Did anyone have a handling problem with the Kawasaki 1100 back around 1996? Kawasaki built these skiis and they had major problems. You would ride and all of the sudden the ski would either go right o...
1997 Sea-Doo GTX. Over the summer, the fuel gauge on the Info Center started only reading 0 - 1 bar whether the tank is full or empty. I figure a magnet fell off of the sender? Anyway, is it possible ...
The oil light came on the other day while riding. Knowing that I couldn't have used ALL the oil (since it was full when I started, and was only riding and hour and a half), I quick stopped and ch...
I have a new 99 Yamaha XL-700 jet ski. I winter-rized it last winter and everything was fine this summer when I went to use it.
The last time I used it was probably June or July. I charged the bat...
first try to keep the problem simple...........im asuming the boat ran fine till the first problem..............please tell how a bolt ended up in the cyl ? second assuming everything else was ok and ...
Some 580's had a recall for these symptoms. Now I know yours is a 720, but the potential for the problem still exists. There was excessive rotary valve clearance. This could also be a problem for...
got a problem with my HX ,when you start off from the beach, hot or cold, the motor 'burbles' and takes a few moments to 'clear out' before it runs fine with good throttle response...
I started my ski up outside of the garage this weekend and as soon as it started I could tell there was a problem. I let it run for about ten more seconds, shut it off and started it again. I blipped ...
...e replaced them (coincided with 10hr service, what a surprise). Plugs were the first thing I replaced when problem started (which was immediately). So knew mechanic was wrong but took his word for it ...
...
I'm sorry but I only beleive in internet media anymore, internet media can be edited if their is a problem, it is current, instead of three months old! Just like snail mail with stamps and suc...
No problem Don!
Scotty Wrench
Money may be a problem, unless your webpage was a HUGE success...
No problem! Good luck with the paper!
Scotty Wrench
Gotta Agree with George-.005 difference will cause a problem with any head.
Fagan Pace
...oes the same thing. It is a pain to start when it is stone cold but when it finally gets going there is no problem. Would a primer help this?
Thanks, Jetskiboy...
how do i cap off the oil pump? i know these have some kinda problem getting oil to the 3rd cylinder .and why dose the jetski need to be turned a certain way after u fall off of it.
Boy you have a problem. If stock yamaha coil is not providing output needed, and See Doo is, then which one offer more reliability? Measure twice cut once.
I have two on my sxipros. no problem what so ever, if you adjust the static trim (normally some form of mechanical stop) the same as a non drop and if the dia is the same..no difference in speed. Afte...
Ya he should go to this website so he sees that the problem is operator related... failures only happen to morons who have the poor brain capacity that arend does. This guy must be KDA's illegiti...
... agree with you on the possibility of just install a t-stat. I was just curious if anyone really has had a problem. Of course, I don't think anyone else on here was nosy enough to even know they ...
There are cheater ways to do it, but if you have the motor out, it probably was to fix a problem. Spend the bucks and get it aligned properly. Same with rotary valve timing. It is worth spending a few...
...ded teh internal filter to be cleaned on the carb.. wouldnt get out of its own way.. even if thats not the problem.. couldnt hurt.. and might as well rebuild the carb while you have it off...
...ing too. Karen is getting my Mobby's suit and I was in the market for another one for myself.....Well problem solved and at a sweet price.
Later, Matt Burkhard
...
...t on, slowed down, water went in gas tank...I estimate a cup or a little more, made it back to the dock no problem. What should I do?? I am hoping there is a quick fix!...
The shaft is not the problem, the screws are. The shaft you sell is sweet, but are you going trust Joe Public to properly secure the butterfly screws? You have lawyers, right? Good luck.
Just lucked into a Wave Blaster real cheap. Needs a motor and pump. Was stolen and stripped. Engine is no problem, planning a motorcycle engine for it. But I need a pump. Basically everything. Anyone ...
...39;ve ordered a few little parts from them for the old lady's sea-doo, and never run into any type of problem. They do have a minimum order, I think it's $20. Matt
...
Harry Lloyd has done more for this sport than anyone I know, so what is your problem. He took Rick Roy in & helped him train when he first started in USA. every time I went down to Fla. we rode to...
... boat or bigger jetski?? I know the skier would propably pull my jetski around, but it shouldn't be a problem if the skier is light enough and won't do big turns......
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...