intake
I have a 98 sxi pro and my stock intake manifold cracked at the the same place yours did. If fact i had 2 crack and break. First intake manifold that broke was under warranty and did no other damages ...
does anyone make a screen for the intake grate on a yamaha waverunner
Sold my XLL. I got a GroupK Modified ride Plate $50.00, R&D Intake grate $75.00
I was wondering if anyone has tried a Jet Dynamic intake grate for the Pro? I have tried all the standard type twin bar single scoop type grates and off course the R&D double scoop which turned gr...
I just recently installed 42 mm Keihins on my stock intake manifold with Moto reeds. I think I made a mistake on the manifold because I ported the intake to the same diameter as the Moto reeds.
It...
Thanks for the post. I am very much interested in your test results. I haven't done anything to the intake track except remove the 'bulb' and redirect the port side air intake hose to a...
...;s. #1) 1995 Kawasaki 750SXi (standup) - One of the HOTTEST standups ever built. No mods, MINT condition, Intake Grate, Ride Plate, Dual Carbs(factory) - #2) 1994 Yamaha Wave Raider - Riva head, Intak...
The only way I know how is to take the carbs and intake manifold off.
I would like the R&D intake. I emailed you. I am at
Before you buy.
Does this intake grate live up to its claims?
You have to inspect them by removing your intake. You did not say what ski & year.
Does anyone know where I can find an intake manifold for a Sea-Doo HX (720 engine) that allows the use of 46mm carbs along with
...ed-Master ride plate for the Ultra yet? I am interested in it's performance and what other bolt-ons (intake, sponsons, etc.) were used with it.
Thanks,...
Hi, will the worx intake grate work on a 2001 XPL
(1 hole at front of grate)
...5 GAS GUAGE-20 MOTOR MOUNTS-30 FOR 3 BLACK SPONSONS-15 ONE PURPLE-10 STORAGE BUCKET W/ CANISTERS-35 STOCK INTAKE MANIFOLD-35 BUCKSHOT INTAKE-40 MILLED HEAD(ONE BAD DOME)-20 STOCK CARBS-100 TANK STRAPS...
...ever owned
heres a list of the goodies finger throttle renthal bars primer kit reed stuffers jetsport intake manifold 38 mm mikuni westcoast limited pipe(most h.p. pipe they made) westcoast racing...
... the 1100 raider, 95 model . The set was removed after 15 hours of use. Replaced with 44's. Need the intake,too? How about the fuel pump?...
just use a sandpaper roll to knock off flashing/do not sharpen edge /spend your time sealing pump intake and anywere air can hide in pump assy. chip de
The 2 intake tracts behind the rotary valve have a step relief on the bottom of both openings. Thewre is also a very small hole drilled at the bottom of the step. Does anyone know what purpose this se...
...went one way the ski went the other. was fun at first till it happened a couple of times. blueprinted the intake grate & it was fine after that, also had to fix how it was positioned in haul.> ...
...D TO REPLACE A ENGINE HAVE A POWER VALVE 1200 CAN I REPLACE IT WITH A NON VALVE ENGINE.WILL EXHAUST/CARBS/INTAKE BOLT UP?...
Stock ??????
R&D Air filter, R&D Intake grate, R&D ride plate, Solas Prop, rejetted carb's, sealed pump shoe, sponsons, hours of R&D.
It maybe stock by the rule book but i...
... your bunks go, I can't remember what that parts called) and then also build up the middle where the intake goes. I had air bubble problems but it worked out pretty good in the end. You can use a...
On my 98 sxi pro i had 2 stock intake manifolds break. They both broke in the same place. The spot where the threads are on the manifold breaks off. One of the intake manif ds that broke caused my mot...
...omething however, my experience with this particular model points to a different but related culprit. The intake tunnel is a large one piece insert that is sealed to the hull with a foam packing type ...
...Tec ported cylinder for superstock GP 1200 ~ 400.00 Pro-Tec heads 175 & 195 psi ~ 150.00 each Pro-Tec intake manifold ~ 150.00 Taper bored 44mm carbs on a Pro-Tec manifold ~ 450.00...
...d it.I took the STX out, after riding in the chop, I decieded it needs some mods. I ordered wider bars,an intake grate, sponsons, and for sure mats ( those stock ones are almost as bad as the OE Ultra...
...rmance Charging Lightwieght 785 flywheel $100
R&D 82mm venturi nozzle $75
R&D Direct Flow intake manifold $75
Seadoo 785 Billet head anodized clear with race and pump gas domes ( 1...
...r (Kaw 650) - $40
Mikuni SBN 44mm - $75
Mikuni Dual SBN 44mm w/ Prok atomizers - $175
R&D intake manifold for dual Mikuni 44mm - $30
Keihin dual 38/40 CDKII (GroupK modified) - $17...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...