hull
93-94 Waveblaster hull for sale. This was a Yamaha test hull and it is missing the pump section. Perfect for a custom pump upgrade or 1200 conversion. There is no hood and most bolt on parts are gone ...
...#039;t know about top end. Can you find a copy of the SeaDoo racing handbook? It has a whole section on hull truing. Basically, they say to go over the hull from bow to stern with a long board sander ...
I would like to include a survey in the report I am writing about PWC hull design. Please help me out and respond to this, besides, it might be interesting to see what everyone says. Remember, all of ...
I have a friend who wants to buy a carbon fiber hull or a lighter composite GP hull material. I know Bullet has their's but....7 grand is not what this guy wants to pay. If anyone has a used one ...
After years of my abuse, the chines of my SJ hull were pretty worn down. First, I sanded the entire bottom with a 5' disc sander and 80 grit tp 150 tp remove all the paint and smooth out the deep...
...g out with a redesigned watercraft to be released in 2002. This 2001 model year marks the end of the SL hull and deck. From what I hear they will be a much more aggressive V-hull style unlike the mod-...
...R... I dont like it one bit.. My GTX will smoke it out of the hole...Plus that thing is a barge.. Shamu hull.. I am also not at all hot about that SMC hull...Sheet Molded Crap
I like the Kawa Ultr...
...tty sure it will crack again.
He is fixing the gel coat on the bottom and cutting the inside of the hull out (motors out) and putting either aluminum or balsa wood inside the hull to reinforce the...
Mark I just need through hull outlet. I think its two pieces.
That's an easy one. A cheater hull and an sanctioning body who was too afraid to do anything about it.
Sharky
No, but I was thinkin of puttin a Kawasaki 440 motor in a Yamaha SUV hull.
...to 1990. The GT580 had twin ones and had an external fuel pump with ASOV mounted on the interior of the hull....
...' stock because imo, the type of riding I do would bend it, plus it would not end up flush with my hull....
...t happens when that billet plug hits something hard? It smashes through the bumber piece and cracks the hull. Nice!!! It wont crush like the stock plastic plugs....
Selling 1997 HX Hull with engine less head/exhaust/carbs with UMI steering, Skat-trak prop. $700.00 OBO
...e would be fine, but low speed fun (spin-outs, fishtails, etc) is on the low end of the scale do to the hull design of these 155hp craft and the weight of them.
Gp800r - Same basic hull as the 155...
The reason Sport Class boats have been discontinued has nothing to do with speed or hull design. Niche boats quit selling in favor of larger barges.
Sharky
... three cyl. I have the VIN number. Does anyone know what the numbers mean? Here it is: PLE03324A694 The hull paint is worn, the impeller is pretty beat and the thing was stored improperly so the carbs...
Pretty motivating, 1 mph is pretty significant for an Ultra hull. Anyone have this 'actual' plate on theirs?
and run me over, wreck) yeah that one! I would consider this plate seriously ...
...e easiest watercraft out there to start and use. Fuel economy is fantastic, the ride is smooth, and the hull is predictable. Just my opinion.
Tom Beesley's Point SeaDoo...
... stroker 800cc engine 4 inch extended pump msd total loss dual 47 buckshots and a custom tried and true hull now my wifes limited goes 57mph aint that a shame I spent so much on my sx
...
...the better the hook-up (but don't go below .006' or pump 'crashing' can occur do to hull and prop flex in rough conditions)
Nate...
... way there. Its physics, the motor needs BOTH gas AND air. Why dont you hook up an air tank inside your hull, you could even hook up a buddy breathing device so that you can breath also. Just go ahead...
...ke into count a new engine. It looks like it is in better than average condition, and the inside of the hull is very clean....
...to a different but related culprit. The intake tunnel is a large one piece insert that is sealed to the hull with a foam packing type seal. If this seal is disturbed or breached the boat will react mu...
...do about it. meantime i got a bit of a project going myself. wedged a honda CBR motor into a sea doo sp hull. 6 gears and a clutch. yeeee haaa. don't have a clue how its going to work yet, but it...
...nefit people looking to buy in the spring. There needs to be more 'routine maintenance' tips, hull protection, etc. They could more stories about which states & lakes are 'PWC frien...
...iner head. Great for jumping and sliding.
Walt, did you get to look at it when you picked up the X2 hull?
Jeff...
... our crew will be given a brand new 2002 Honda PWC when they roll off the production lines. Significant Hull changes since we started have allowed us to gain 3-4mph. The new Hulls alone should put 1 o...
...
I owned one in the past had it for 8 years before i got rid of it.. The ski has pretty much a flat hull.. Turning needs a semi wide area.. This ski will not turn on a dime unless you swing the ba...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...