engine
Well thanks to kawasaki and the lack of quality that was put into my brand new jet ski, the engine has decided to take a vacation....71 hours and the engine is wiped...#1 & #2 cylinder 75 lbs. com...
Can someone who has access to a parts diagram for the Sea-Doo Vertical RAVE engine of the early 90ies, please help me locate a part number from that engine?
Are there any secrets to aligning an seadoo engine without the seadoo alignment tool?
Or am I going to have to take it to a shop here in Jersey?
Say IF you are right and I don't fix it, can this do major damage to the engine?
I really think its beceasue the ski has not be started for a while and just it like the residue. Like if you s...
Ok, I can't even give my XP away unless the engine runs, so I've decided to rebuild it. It looks as if the rear piston was actually hitting the head, in other words, no squish gap. And no I ...
...39; (at least that's what I call it) high-temp paint that they've been using on the 750 and 900 engines for the past few years?
It wasn't listed on any of the online microfiche page...
Just curious...... I'm going down to the dealer tomorrow to seal the deal on an '01 STX.
That is the difference between people who think that they are engine builders because they can bolt parts together and actual 'engine builders'! Who was it that stated, 'God is in the d...
I was able to get the engine running Friday night. Still believe water was an issue.
Anyhow went to a lake Saturday and could not keep engine running (a lot of times it would not start without sta...
how much for the engine, and what all would you include with the engine, and how many hours on the engine
What do you guys think about a 1996 XP with a zero-hour 800 engine in it? I found this ski at a local dealer. They just replaced the engine and are asking $3800 for it, including a single trailer. It ...
Smoke in the engine compartment is not a sign of bad reeds, but it is the reason your Ultra is not running right. You have an exhaust leak somewhere and it's choking the engine once enough smoke ...
Just lucked into a Wave Blaster real cheap. Needs a motor and pump. Was stolen and stripped. Engine is no problem, planning a motorcycle engine for it. But I need a pump. Basically everything. Anyone ...
...ld result in serious damage, specially if bore to piston clearance is tight. I like to see 120 F on avery engine. Do not forget to set up fuel delivery according to RAD. PS. Do not fall for the popula...
NEED TO REPLACE A ENGINE HAVE A POWER VALVE 1200 CAN I REPLACE IT WITH A NON VALVE ENGINE.WILL EXHAUST/CARBS/INTAKE BOLT UP?
Every case ported engine I've seen has that part removed. I asked the same question a couple of years ago and I believe Mr. HPT was suggesting that it is there to help the engine start easily. My...
I use the hose adapter flush kit to flush the motor. Do I need to rev the engine when flushing out sea water? Or can I just have the engine idle (about 3000 RPM) while the adapter is connected, and if...
I have experimented with different length cones in the pump of my GP1200 and found the engine to be very sensitive to the extra load applied . Losses in Rpm of 100 -300 rpms are typical , yes a slight...
...s You'll Need:
Trickle charger
Cement blocks or jacks
Steel wool or rags
Cover
Draining the Engine and Cleaning the Jet Ski
Step 1Drain the water from the engine as soon as you take it ...
...ant to do a short block swap. This is worst case scenario and you might not even need to do a swap if the engine is ok? Just some TLC can bring it back to life. Check the pump stator and make sure it ...
...ck and the idle speed set to 2500. Now in addition to craft bogging I get exhaust temperature warning and engine does'nt stop when lanyard is pulled. Craft is now in the shop for the 3rd time. Al...
...ennzoil etc) really minimize ring and cylinder wear more than dino oil at 40:1, ? I've got to get an engine from SBT or somewhere else in the spring, and plan on breaking it in on mineral oil at ...
I read 3 or 4 posts about SeaDoo closing down next year...... Do you think its their lack of engine quality, or is it that the other companies are developing new 21st century stuff and they are not? I...
Does anyone know if any other engine would be able to fit in a Wavejammer aside from a 500? Anynone ever done this?
Now I don't know if I should get one. Maybe, the XP. hmmm... How fast is the rxdi? Any engine problems?
Motor...Engine... whos counting (besides you George)...
Scotty Wrench
I wanted to say Engine Trix? I remember someone posting about them a long time ago.
Does anyone know where I can find an intake manifold for a Sea-Doo HX (720 engine) that allows the use of 46mm carbs along with
Check out SBT http://www.enginenet.com/ . They are a well known PWC engine supplier..
Charlie Z
I have a Polaris 2 cylinder engine that I need to replace. Anyone have a good source for a rebuild? Im located in Florida.
Thanks
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...