carb
Hi everyone ,
looks like a cool site.
I have a question , On a Mikuni carb is the valve body assembly different from one to another,
Reason im asking was doing a carb overhaul and cant get t...
... be casting flaws, or improper drilling and tapping, but the most likely the cause is over torquing the carb mounting hardware.
While I'm not saying that you were at fault, one thing anyone w...
info came from yamaha manual at dealership! It was update for high altitude carb & prop setups BUT they have stock standard setting for sea level Best I can tell you for now will call tec.line and...
How many turns out on the carb mixture screws is equal to 1 jet size? Also does this ratio apply to the Mikuni 'I' series carbs also?
The stock setting for the low speed screws on the GP...
Howdy,
Does anyone know these settings? My dealer said Yamaha does not provide them.
Thanks,
... local Yamaha shop said maybe I have bad fuel since it sat up for a few months. He said maybe I need my carburetor cleaned if that doesn't work. He said everything might have gotten gummed up.
...
my 92 waverunner III needed teh internal filter to be cleaned on the carb.. wouldnt get out of its own way.. even if thats not the problem.. couldnt hurt.. and might as well rebuild the carb while you...
I have seen six failures of the stock int.man. I have also seen two cases of carb butterfly srcews back out and go through the motor. Rumor has it that many of these boats were 'hand built'....
Leaky needle and seat in the carb? Anyone else think so? Next time, before you get on, turn the fuel to OFF, get on normally, then turn it back on and see what happens. If that fixes it, it's pro...
how much do you want for all the carb jets?? let me know, J in tacoma
what carb's you running? chip de
...ey actually did to your ski? Give us all the info you have to try and help out. I still think it's carb or cat related even though it's brand new....
...andup ski with more than 75 hp. 1995 is the only year that Kawasaki released both 750SX (63 hp - single carb) and 750SXi (75 hp - dual carb). 75hp is (IMO) quite adequate for most people. Most diehard...
Westcoast heads are definetly not the best heads for that ski. Novi's are the best carb on the market!
Bill O', I need the phone # to WCM. I have a friend with a 2000 RX that needs some mods done.. Carb jetting kit, F/A's, Grate and whatever else you recommend.. This is strictly for recreatio...
...'s lean on the mixture. Your blowing the flame out with too much air, and not enough gas. When the carbs were redone did they clean the internal filters or replace them?? Where the adjusters mess...
Yes James, I added an extra pulse line. I also matched the mating surfaces of the carb and manifold, 43mm I believe. Smoke also comes out of two of the carbs when I stop the motor. These are the first...
Nathan,
On some CV carb equipped Kawasakis (not all but some) will exhibit the mid range lean condition and seizure could occur, even on a stock boat. It is best to leave the chokes in place on th...
Stock ??????
R&D Air filter, R&D Intake grate, R&D ride plate, Solas Prop, rejetted carb's, sealed pump shoe, sponsons, hours of R&D.
It maybe stock by the rule book but i...
...light and quick. I imagine if a 650 would fit in there, so would a 750. It ran 45mph after I put a 44mm carb and a Mariner head. Great for jumping and sliding.
Walt, did you get to look at it when...
...old new battery this season skat track impellar ocean pro quadrafin R&D axial flow intake grate The carb has been properly jetted to the mods(which are all bolt ons > I removed oil injection I ...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 My Jetski Buddies |
TIP: Write your question in details [ why? ]
Latest Posts
|
more posts...